I used the SpyderX Elite because that’s what Datacolor sent me, but for my own personal needs, the SpyderX Pro would suit me just fine. There are two versions of the SpyderX to choose from. This may vary slightly computer to computer, but I found 2 minutes to be about the same across all of my computers.įeature Comparison of the SpyderX Pro & SpyderX Elite However, once you’ve done it a couple of times, this whole process takes about 2 minutes from the moment you launch the software until you press “quit”. The first time you calibrate, it may be a bit clunky a you play around with settings and whatnot. This isn’t something I get into, but that’s the end of the process. Step thirteen: There’s a graph and some other options to compare different sorts of calibrations. You may be quite surprised about what you see if this is your first go at calibration. Step twelve: You can check out what your screen looked like before and after calibration. Step eleven: The calibration has been completed, now you need to name the calibration, press save and set your calibration reminder. I just learned that on the 5K iMac, you can hold OPTION+SHIFT while raising and lowering the brightness in smaller increments (thanks MikeTCool). On some monitors, this may be difficult, as there may not be enough steps of brightness to nail it. You’re supposed to set the brightness so it gets to within 4% of the brightness level you selected. You need to set the brightness of the screen to match the target you selected earlier. Step ten: The calibration stops for some manual input. Step nine: The software now begins the calibration. Step eight: Here’s the SpyderX Elite ready to go. The base plate used as a weight on the back of the screen to help keep the colorimeter in place. I tend to have to tilt the screen on the 5k iMac to make it sit flush. Step seven: Now it’s time for the magic, take the base off your SpyderX Elite and place it on your monitor. Don’t have any sort of direct artificial light or sunlight hitting the display, the software will let you know if your ambient light is too bright for best results. Step six: The SpyderX Elite will now calibrate the ambient light around your monitor to help get the best calibration possible. I tend to always use the recommended settings with the FullCAL selected. Step five: Select the calibration settings you want to use. The “Expert Console” is above my paygrade. The “Studio Match” will help you get multiple displays to look as close to the same as possible. In our case, we’re doing the “step-by-step assistant”. Step four: Select what sort of calibration workflow you want to use. There are some guidelines here to help you select the correct type of technology inside your monitor. Step three: You need to select what sort of monitor you’re going to be calibrating. Step two: You’re presented with a checklist on how to get the best out of the calibration. For the purpose of this review, we’re only doing the “Calibrate My Display(s)” option. Step one: You simply select what you’re wanting to do with the SpyderX Elite software. The SpyderX Elite has an all-new and larger lens-based system that Datacolor claims has increased accuracy and speed of calibration and we definitely see merits in both claims. However, since I only calibrate every month or so, speed isn’t a huge deal for the home user, but it could matter for a studio or educational facility with many monitors to calibrate. I found the speed to be about 50% faster than the Spyder5 Elite I graduated from. This latest calibrator from Datacolor is their fastest and from what I can tell, the most accurate one I’ve used. I have always purchased or accepted each new version since the Spyder2. I have been using Datacolor calibrators since the Spyder2 and I have always been impressed by their software and the performance of the calibration tools. However, I do have eyes and matching my editing to third-party printing is very important to me. I am not an expert on color science or printing. I’ve always been a bit taken aback by how many photographers I’ve run into over the years that don’t utilize a relatively inexpensive tool to get the most out of their monitors.įull disclosure: Datacolor sent me a SpyderX Elite for free and they have been an active sponsor of Canon Rumors over the years.įuller disclosure: I am not a reviewer at the best of times, so this is an honest review of the feature(s) I use, and does not discuss every single feature available to you. We may receive a commission for purchases made through these links.Ī monitor calibration tool is something I’ve always recommended to photographers, from hobbyists to professionals. This site contains affiliate links to products and services.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |